Az oldalunk használhatóságának érdekében sütiket (cookie) használ, amelyek leírását az adatvédelmi tájékoztatónkban találod. Rendben
PREMIUM TUNING
AKCIÓK! HÍREK
Induction Kit for Hyundai i30N and Veloster N
Kattintásra galéria nyílik
Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N Induction Kit for Hyundai i30N and Veloster N
396,86 USD
Áfával Áfa nélkül
Tedd a kosárba!
A bruttó ár (Áfával) 0% áfát tartalmaz, amennyiben a postázási vagy átadási ország: United States
Gyártó
Cikkszám: AZPFMINDK28
Gyári cikkszám: FMINDK28

Rendelésre!
A kiszállítás várható napja:
2024.11.30

Hyundai

i30N 2018-

Veloster N 2019- T-6DI

Forge Motorsport are excited to release our industry leading intake for the Hyundai i30N. This aftermarket cold air intake system improves your i30N’s airflow in several key ways. It routes the air more directly into your engine, using a huge 102 mm diameter CNC mandrel bent alloy pipe. The aftermarket system also improves the airflow by adding a high-flow, high efficiency air filter in place of the more restrictive factory air filter. Finally, the cold air intake system is set up to allow cooler air to easily flow into your engine

The intake diameters on these air intakes have been carefully tuned to provide exactly the correct quantity of air ensuring solid consistent power gains throughout the rev range without any loss of low-end torque. The pipework is specifically designed to feed the turbo without interruption. The upshot to all of this is a gain of induction acoustics under acceleration, which improves the driving experience and adds a bit more drama to the Hyundai’s 2.0 four pot engine.

As always filtration is important when developing an intake, so we once again turned to the industry leaders and Forge long term filtration partners Pipercross.

With over 25 years’ experience in both the domestic and motorsport market they recommended a multi-layer foam construction filter, these filters work perfectly in our ‘Hi-Flow’ range. The large filter provided flows 60% more air than the stock filter.

The intake is finished off with our unique black thermal powder coating. This kit comes with Forge’s usual detailed fitting guide to help make installation as easy as possible.

Hyundai boast figures of 275bhp and 278lb.ft on their standard vehicle. When we ran our CAT backed performance exhaust development vehicle on the dyno with this intake it reached figures of 296bhp and 310lb.ft!

Interestingly there has been lots of divided opinions about our intake requiring a heat shield. Testing took place with the bonnet shut and replicated wind speeds of around 70MPH. Intake temperatures were logged and monitored along with thermal images taken,. During this testing, we did not see the inlet pipe or intake temperatures rise; even after 4 hard pulls, the inlet temperatures stayed at a steady 30°C.

Why not add gold tape to the underside of the aluminium housing to further reflect any heat soak from the engine. The Gold tape comes on a 5 metre roll allowing you to apply it to the underside of your Forge Motorsport product.

In the Box:
1 x Black Alloy Hard Pipe
1 x Pipercross Filter
1 x Valve Silicon Joiner
2 x Hose clamps

Értékelések átlaga

Nincs értékelés